HANTEKOscilloscopes
Model: DSO5000P
DSO5000P Series
Price:Price on Request
Installation Category II: derate at 20dB/decade above 100kHz to 13V peak AC at 3MHz* and above. For non-sinusoidal waveforms, peak value must be less than 450V. Excursion above 300V should be of less than 100ms duration. RMS signal level including all DC components removed through AC coupling must be limited to 300V. If these values are exceeded, damage to the oscilloscope may occur.
Key Specifications
Sample RateDSO5202P: Real-Time Sample: 1GS/s Equivalent Sample: 25GS/s
Acquisition ModesDSO5202P:
NormalDSO5202P: Normal data only
Peak DetectDSO5202P: High-frequency and randon glith capture
Sample RateDSO5202P: Real-Time Sample: 1GS/s Equivalent Sample: 25GS/s
Acquisition ModesDSO5202P:
NormalDSO5202P: Normal data only
Peak DetectDSO5202P: High-frequency and randon glith capture
AverageDSO5202P: Wavefom Average, selectable 4,8,16,32,64,128
Inputs CouplingDSO5202P: AC, DC, GND
Inpits ImpendanceDSO5202P: 1MΩ±2% ‖20pF±3pF
Probe AttenuationDSO5202P: 1X, 10X
Supported Probe Attenuation FactorDSO5202P: 1X, 10X, 100X, 1000X
Maximum Input VoltageDSO5202P: CAT I and CAT II: 300VRMS (10×), Installation Category; CAT III: 150VRMS (1×); Installation Category II: derate at 20dB/decade above 100kHz to 13V peak AC at 3MHz* and above. For non-sinusoidal waveforms, peak value must be less than 450V. Excursion above 300V should be of less than 100ms duration. RMS signal level including all DC components removed through AC coupling must be limited t
Sample Rate RangeDSO5202P: 500MS/s--1GS/s
Waveform InterpolationDSO5202P: (sin x)/x
Record LengthDSO5202P: 40K
SEC/DIV RangeDSO5202P: 2ns/div to 80s/div
Sample Rate and Delay Time AccuracyDSO5202P: ±50ppm（at over any ≥1ms time interval)
Offset RangeDSO5202P: 2ns/div to 8ns/div; (-8div x s/div) to 20ms; | DSO5102P: 20ns/div to 80us/div; (-8div x s/div) to 40ms; 200us/div to 80s/div; (-8div x s/div) to 400s
Delta Time Measurement Accuracy (Full Bandwidth)DSO5202P: Single-shot, Normal mode:± (1 sample interval +100ppm × reading + 0.6ns); >16 averages:± (1 sample interval + 100ppm × reading + 0.4ns); Sample interval = s/div ÷ 200
Vertical ResolutionDSO5202P: 8-bit resolution, all channel sampled simultaneously
Position RangeDSO5202P: 2mV/div to 20mV/div, ±400mV; 50mV/div to 200mV/div, ±2V 500mV/div to 2V/div, ±40V; 5V/div to 10V/div , ±50V
BandwidthDSO5202P: 200MHz | DSO5102P: 100MHz | DSO5072P: 70MHz
Rise Time at BNC( typical)DSO5202P: 1.8ns | DSO5102P: 3.5ns | DSO5072P: 5ns
MathDSO5202P: +, -, *, /, FFT
FFTDSO5202P: Windows: Hanning, Flatop, Rectamgular, Bartlett, Blackman; 1024 sample point
Bandwidth LimitDSO5202P: 20MHz
Low Frequency Response (-3db)DSO5202P: ≤10Hz at BNC
DC Gain AccuracyDSO5202P: ±3% for Normal or Average acquisition mode, 10V/div to 10mV/div; ±4% for Normal or Average acquisition mode, 5mV/div to 2mV/div
DC Measurement Accuracy, Average Acquisition ModeDSO5202P: When vertical displacement is zero, and N ≥16:± (3% × reading + 0.1div + 1mV) only 10mV/div or greater is selected; When vertical displacement is not zero, and N≥16: ± [3% × (reading + vertical position) + 1% of vertical position + 0.2div]; Add 2mV for settings from 2mV/div to 200mV/div; add 50mV for settings from 200mV/div to 10V/div
Volts Measurement Repeatability, Average Acquisition ModeDSO5202P: Delta volts between any two averages of ≥16 waveforms acquired under same setup and ambient conditions
Trigger TypesDSO5202P: Edge, Video, Pulse, Slope, Over time, Alternative
Trigger SourceDSO5202P: CH1, CH2, EXT, EXT/5, AC Line
Trigger ModesDSO5202P: Auto, Normal, Single
Coupling TypeDSO5202P: DC, AC, Noise Reject, HF Reject, LF Reject
Trigger Sensitivity (Edge Trigger Type)DSO5202P: DC(CH1,CH2): 1div from DC to 10MHz; 1.5div from 10MHz to 100MHz; 2div from 100MHz to Full; DC(EXT): 200mV from DC to 100MHz; 350mV from 100MHz to 200MHz; DC(EXT/5): 1V from DC to 100MHz;1.75V from 100MHz to 200MHz; AC: Attenuates signals below 10Hz; HF Reject: Attenuates signals above 80kHz; LF Reject: Same as the DC-coupled limits for frequencies above 150kHz; attenuates signals below 1
Trigger Level RangeDSO5202P: CH1/CH2: ±8 divisions from center of screen; EXT: ±1.2V; EXT/5:±6V
Set Level to 50%(typical)DSO5202P: Operates with input signals ≥50Hz
Video TriggerDSO5202P:
Video Trigger TypeDSO5202P: CH1, CH2: Peak-to-peak amplitude of 2 divisions; EXT: 400mV; EXT/5: 2V
Signal Formats and Field Rates, Video Trigger TypeDSO5202P: Supports NTSC, PAL and SECAM broadcast systems for any field or any line
Holdoff RangeDSO5202P: 100ns ~ 10s
Pulse Width TriggerDSO5202P:
Pulse Width Trigger ModeDSO5202P: Trigger when (< , >, = , or ≠); Positive pulse or Negative pulse
Pulse Width Trigger PointDSO5202P: Equal: The oscilloscope triggers when the trailing edge of the pulse crosses the trigger level. Not Equal: If the pulse is narrower than the specified width, the trigger point is the trailing edge. Otherwise, the oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width. Less than: The trigger point is the trailing edge. Greater than (also called over
Pulse Width RangeDSO5202P: 20ns ~ 10s
Slope TriggerDSO5202P:
Slope Trigger ModeDSO5202P: Trigger when (< , > , = , or ≠ ); Positive slope or Negative slope
Slope Trigger PointDSO5202P: Equal: The oscilloscope triggers when the waveform slope is equal to the set slope. Not Equal: The oscilloscope triggers when the waveform slope is not equal to the set slope. Less than: The oscilloscope triggers when the waveform slope is less than the set slope. Greater than: The oscilloscope triggers when the waveform slope is greater than the set slope.
Time RangeDSO5202P: 20ns ~ 10s
Overtime TriggerDSO5202P:
Over Time ModeDSO5202P: Rising edge or Falling edge
Alternative TriggerDSO5202P:
Trigger on CH1DSO5202P: Internal Trigger: Edge, Pulse Width, Video, Slope
Trigger on CH2DSO5202P: Internal Trigger: Edge, Pulse Width, Video, Slope
Trigger Frequency CounterDSO5202P:
Readout ResolutionDSO5202P: 6 digits
Accuracy (typical)DSO5202P: ±30ppm (including all frequency reference errors and ±1 count errors)
Frequency RangeDSO5202P: AC coupled, from 4Hz minimum to rated bandwidth
Signal SourceDSO5202P: Pulse Width or Edge Trigger modes: all available trigger sources The Frequency Counter measures trigger source at all times, including when the oscilloscope acquisition pauses due to changes in the run status, or acquisition of a single shot event has completed. Pulse Width Trigger mode: The oscilloscope counts pulses of significant magnitude inside the 1s measurement window that qualify
Cursor MeasurementDSO5202P: Voltage difference between cursors: △V Time difference between cursors: △T Reciprocal of △T in Hertz (1/ΔT)
Auto MeasuermentDSO5202P: Frequency, Period, Mean, Pk-Pk, Cycli RMS, Minimum, Maximum, Rise time, Fall Time, +Pulse Width, -Pulse Width, Delay1-2Rise, Delay1-2Fall, +Duty, -Duty, Vbase, Vtop, Vmid, Vamp, Overshoot, Preshoot, Preiod Mean, Preiod RMS, FOVShoot, RPREShoot, BWIDTH, FRF, FFR, LRR, LRF, LFR, LFF
Display TypeDSO5202P: 7 inch 64K color TFT (diagonal liquid crystal)
Display ResolutionDSO5202P: 800 horizontal by 480 vertical pixels
Display ContrastDSO5202P: Adjustable (16 gears) with the progress bar
Output Voltage( typical)DSO5202P: About 5Vpp into ≥1MΩ load
Frequency(typical)DSO5202P: 1kHz
Supply VoltageDSO5202P: 100-120VACRMS(±10%), 45Hz to 440Hz, CATⅡ 120-240VACRMS(±10%), 45Hz to 66Hz, CATⅡ
Power ConsumptionDSO5202P: <30W
FuseDSO5202P: 2A, T rating, 250V
TemperatureDSO5202P: Operating: 32℉ to 122℉ (0℃ to 50℃); Nonoperating: -40℉ to 159.8℉ (-40℃ to +71℃)
Cooling MethodDSO5202P: Convection
HumidityDSO5202P: +104℉ or below (+40℃ or below): ≤90% relative humidity; 106℉ to 122℉ (+41℃ to 50℃): ≤60% relative humidity
AltitudeDSO5202P: Operating: Below 3,000m (10,000 feet); Nonoperaring: Below 15,000m(50,000 feet)
SizeDSO5202P: Length 385mm, Width 200mm, Height 245mm
WeightDSO5202P: 3.5KG(with Packing); 2.08KG(without Packing）
  
HT300B,HT500BDescription: 350Mhz,500MHz,10:1/1:1 | View Manual: Download
HT-100B，HT-200BDescription: 100MHz,200MHz,10:1/1:1 | View Manual: Download
PP500BDescription: 500MHz,10:1/1:1 | View Manual: Download
PP-80,PP-150,PP-200Description: 60MHz,100MHz,200MHz,10:1/1:1 | View Manual: Download
PP80B, PP150B, PP200B, PP300BDescription: 80Mhz, 150MHz, 200MHz, 300MHz, 10:1/1:1 | View Manual: Download
PP-90Description: 80MHz,10:1/1:1 | View Manual: Download